Making Stocks/Spanish Pony

Joint accuracy is critical to the piece, particularly the junctions between uprights and horizontal legs. Using a dado/lap joint here provides excellent rigidity if done right.

Stock Holes: You need to start with a few measurements of your target occupant.
If you plan to build generically, measure a handful of people and use your judgement.
Size the holes with these:
a) wrists,
b) ankles,
c) neck.
Identify minimum frame height based on how far off the ground their head is when comfortably bent over.
Space upper holes (on crossmembers 1 and 2) by having them comfortably raise wrists into line with neck.
Space lower holes (on both 2/3 and 4/5) at a mild straddle.


Cut the stock boards with holes first (1-5). Two lenghts of 2×6 and three of 2×4. Select this wood carefully, especially avoiding warp across the long side of the cross-section (i.e. 6-inch side). Mark and cut the half-circles in their respective places. Remove most of the wood with a jig or scroll saw and finish up with drum sanding.

Cut and smooth 10 segments of channel stock (metal). Four fit to the ends of the 2x6s, and are roughly 5.5″ long. The rest are 3.5″ or so, fitting to the 2x4s. Round the corners, or they may dig into the wood of your grooves.

Frame Pieces

The segments of the frame require more work. First, cut the two horizontal legs and two uprights from 4×4 stock. Next, you need to remove some wood from these pieces. The following steps can be accomplished on a table saw with a dado blade, a router, or as a last resort with standard table saw blade and chisel.

First, run two grooves the entire length of the uprights, on the inside face. Spacing , width, and depth are determined by your metal channel material. Channel depth should be about 1/4″ less than the depth of the metal stock, providing clearance for the bolt at bottom. Width may need to be as much as twice the metal thickness for a smooth slide. Boards 1 – 3 run in this channel, and they should slide freely. See diagram.

Vertical Channel CutsVertical Channel Cuts

Cut a lap in the outside bottom of each upright as shown below. This lap should be about 1.75″ by 3.5″, but exact width should be slightly less than the width of respective horizontal leg.

The horizontal legs need several cuts in the order shown below. First, cut a 1.75″ deep by 3.5″ wide dado to receive the vertical member. Actual width of this dado should be a hair less than the board it receives. Exact depth should result in an even fit with the respective upright lap. Note that this is a custom-fit process, and means one upright is always associated with a specific leg. Next, run channels down the front inside face of the board, as shown. These are identical to those in the uprights, and receive boards 4 & 5. They stop at the dado you cut previously.. this is easy using a router, but requires a pull-off and set-down process on a table saw. Finally, cut a 1.75″ deep and 3.5″ wide lap to receive the rear brace. See diagram for clarification, and remember that these boards are _mirror images_ of each other!

If you don’t have the tools for these approaches, you can simulate the same frame from multiple pieces of wood, as shown in the diagram below (one half of frame depicted). However, using this approach the stock board ends will slide in the resulting channels. As I indicated earlier, I don’t like this approach.

Simulating the Frame

This set of channels allows the following. Boards 1, 2, and 3 can slide to any location along the vertical channels. Boards 4 and 5 slide along the horizontal channel up to the upright.

Crossmember Braces

Cut the two remaining crossmembers, the front from 2×4 stock and the back from 4×4. Length of these boards is the width of the total frame. Identify this distance by attaching metal channels to board 4 ( used three countersunk drywall screws per segment) and placing it snugly between the horizontal legs, within the channel grooves. Measure between outside edges of horizontal legs. In the 2×4 (front brace), cut a .75″ deep lap, width = width of the horizontal legs. In the 4×4 (rear brace), cut a lap to mate with the laps in rear of horizontal legs. See diagrams.


Four short feet contact the floor, and should be made from 4×4 stock. They are identical, and dimensioned to provide the required ankle clearance. See the diagram in next section.


1. Bottom frame

Do a mock assembly of the entire bottom section of the unit on a flat surface, ensuring that your joints fit and are square. Adjust joints as necessary. Mark locations and drill a 3/8″ hole in each corner. Make sure not to interfere with the channels in the front section. Drop bolts into these holes and check squareness again. Also, make sure that a stock board slides neatly into place. Adjust as necessary.

Stocks bottom frame

Disassemble and continue with the next step. You might want to recess the tops of these four holes slightly with a 1″ spade or forstner bit to accept a washer permanently. Optional, but a nice touch.

2. Uprights

Time to join the uprights to the horizontal legs. Make sure these joints fit tightly and are square. While the pieces are clamped together, drill a 3/8″ hole dead-center of the intersection. This should be directly between the two channel grooves on the upright.

Stocks upright junction

Again, use a 1″ bit to recess both sides of these holes. Depth should equal the thickness of nut + washer. The recess on the inside face of the upright is required to provide clearance for the sliding stock boards. The outside recess is optional.

3. Feet to Legs

Glue the four feet to the undersides of the horizontal legs, about 3.5″ back from the ends. This leaves enough clearance to attach the brace members of the bottom frame. Best approach is to reassemble the bottm frame, inverted, and glue. Liquid Nails is a good choice for this attachment. See diagram.

Front Foot Attachment Diagram

4. Upper Brace

You should have the frame basically assembled at this point. Time to cut and secure the upper brace. Measure the exact distance between the insides of the two uprights at their bottom. Cut the upper brace to an appropriate length from metal stock (I used 1.25″ x 1/8″ mild steel), and secure it to mirror this distance near the top of the uprights. I used 1/4″ x 1″ lag bolts. Don’t bolt through a channel! Make sure a stock board (with metal channels, of course) slides freely along both horizontal and vertical channels. Now is the time to fix it, if there is a problem. “Fixing” means modifying the channels themselves at this point. Once both channels allow free movement along their length when the frame is assembled, you can move to the next step.

4. Lock Holes

If you haven’t done so already, screw the metal channel segments to the ends of board 2. You’ll have to remove them (and the ones on board 4) for finishing, but need to drill through them first.

Stock boards 2 and 4 lock in place within their respective channels at specific places, using 5/16″ bolts running through 4×4 frame and the metal channel. You can drill as many of these holes as desired for flexibility, as long as they’re not closer together than an inch or so. The only _required_ position is with board 2 all the way down against board 3 (unless you don’t want to use the vertical ankle holes).

The first holes for both of these boards should be drilled with the board in place, creating matching holes in 4×4 and metal channel segment. Start by marking a line 3/4″ from the edge along each channel, as shown below. All holes must be drilled on this line. Place board in desired position and drill hole using a 3/8″ bit. You’ll have to use a twist bit for these, since you’re going through both wood and metal. Repeat without the crossmember in place for additional locations with a 3/8″ spade bit. The difference between hole and bolt sizes provides a bit a wiggle room, and trust me, it’s necessary!

Lock Holes Diagram

5. Closures

Boards 1/3 and 5 secure to 2 and 4 respectively with standard hasp-and staple or locking draw latch. This approach allows the free-floating stock boards to lock to their two fixed cousins at any of the positions you’ve drilled for.Bolt the fixed boards into any of the positions you created in step 4. Slide each companion board tightly into place. Secure hasp to one board and staple to the other, in any available position that you prefer.

Finishing Up

You still need to round edges, sand out irregularities, and do the standard surface prep for final finishing. Since you’ve read the plan before starting, you may want to do this to each piece as you go along. Alternately, you can build it as described, then take it apart to sand things. Running some of the sharp edges using a quarter-radius router bit may be a good idea, and is my preference. Coat as usual, with paint, varnish, urethane… whatever your favorite might be. Limit both sanding and coating thinkness within the joints, since they already fit tightly. Attach all hardware, including the metal channels. You are done.

Stock Options 

By using parts of this design or adding additional features, you can make a myriad of unique furnishings. Let’s look at a couple of ideas:

* Free-form stocks. Using the basic boards 1 and 2 (without ankle holes in 2) with a hasp and hinge, you can very easily make disconnected stocks similar to a yoke or the “violin” of medieval times.

* Doorway stocks. By placing channels (wood or steel) on each side of a doorway, you could avoid the frame entirely for an interesting effect.

* Multi-person stocks. This design could easily be enhanced to hold two people. One way is to make it a “double-wide,” securing them side-to-side. A cooler way is to extend the back portion of the horizontal leg and build it identical to the front portion above. One person could occupy the wrist holes while the other is stuck by the head, or you could add more restraining holes. Consider these diagrams:

Multi-person Ideas

Alternatively  – being pony-pain, you can have constructions based on show-jumps where the central bar adds the pain. And if you can’t build one, then simply head over to and buy a ready-made one.

About Post Author

Leave a Reply

Your email address will not be published.

This site uses Akismet to reduce spam. Learn how your comment data is processed.